Seems like a good product, lots of information for the $$ spent.
However, the QC at the factory missed - at least this one.
10-digit of indoor humidity level has dead and weak segments. They are 8-segment numbers and several are either dead or weak on the 10-digit. Giving it 4-stars for now...
Returning for a replacement.
If the replacement works, then I will be happy. I will add information to how it works at that point...
If the replacement shows the same or other defects, my review will be edited/appended and the stars "will plummet".
NOTE: Amazon made the return process painless - they get 5 stars for that!
=================
Update, 02/16/2023 - now 5 stars!
Have owned and used the replacement for ~6 days now.
=> Display on replacement unit has ALL segments for all digits and information visible!
What I like:
-------------------
*Easy to program. I set the clock deliberately "off" enough to check the WWV/NIST receiver. By next morning when it had found the transmitter, the clock was set!
*Very bright display, even in a fully lit room. It can be read from across the kitchen. One small gripe, if they had auto-dimming feature, that would be fantastic. Like I said... VERY bright display...
*Accurate as far as I can tell - indoor seems very accurate (see pics), the outdoor within +/- 2 degrees more or less (see pics). I have to say that outdoor, I am happy with that - I use it to get a general idea of if it is "sweater/fleece or T-shirt" weather anyway, not for precision measurements!
-------------------
I used a Fluke 179 multimeter with a "type K" thermocouple, Fluke 80BK-A to measure against the LaCrosse. The meter is "good for" 0.1 degree resolution with a 1% accuracy between -40F and +752F (!), however the thermocouple is listed as "Accuracy: +/- 2.2 °C or 2% whichever is greater ((0 to 260 °C)".
All measurements were taken before sunrise, to avoid any solar "influence" on the outdoor readings.
=> I will NOT say that my Fluke is more accurate than the LaCrosse station - I have no evidence to support that! And I will not go through the rigmarole of calibrating the thermocouple...
*Outdoor sensor: placed it in the ribbed weather housing (LaCrosse 925-1418) they recommend and attached it to the north side of a 4"x4" post. One gripe there: the screwheads (Phillips) require a very "sharp" (read: new) screwdriver if you don't want to slip and round out the screw heads' "+" grooves. ...and predrill the holes for the screws!
Not so fond of:
-------------------
*The "landscape" weather forecast. Yes, it has trend arrows, etc. But being "old school" I would like the barometer reading in numbers presented. The WX-station I replaced (Ac*rite) had a 12 hour barometer graph with numbers readings, that was nice!
*Minor gripe: the buttons on top are labeled on the backside and since I have my station wall-mounted I need to take it down to read the button labels so I know which one to push (do YOU remember all buttons on all equipment you have?) Will print a label strip and attach on the front for my benefit...
*Minor gripe 2: If they had made the major numbers a little smaller, they could have fit max/min reading numbers in w.o. you having to push the temp button to cycle through and view them...
Summary:
-------------------
*Comes with AC adapter, and uses three AA-batteries for backup
*Has all the information available that I want (except the barometer numbers...)
*Shows trends (with arrows)
*Shows min/max (requires button push)
*Automatic time adjustment through the WWV/NIST receiver
*Very bright and clear display. VERY bright...
*Display is a bit "busy", and they seem to not knowing when to mix graphics, bars, and numbers.
*I believe it to be a "good investment". Time will tell. I will recommend this, but do buy the outdoor housing for the sending unit!
-------------------
The Ac*rite it replaces has served us well, but started to give trouble with the remote sending units, one dying all together and the replacement not staying connected. Whether the connection issue is with the sending or receiving unit I have not figured out. Also, the Ac*rite display was getting very dim (yes, all new batteries and AC adapter connected) and the brightness is set to 100%... Perfect for a completely dark room, however, my kitchen is not. Can't complain - had it for MANY years...
Add to your order
-
Coverage for accidental damage including drops, spills, and broken parts, as well as breakdowns (plans vary) -
24/7 support when you need it. -
Quick, easy, and frustration-free claims.
Cover this product:
2-Year Protection $4.99
3 Year Lawn & Garden Extended Protection Plan $6.99
Cover all of your eligible devices:
Asurion Complete Protect: One plan covers all eligible past and future purchases (Renews Monthly Until Cancelled) $16.99/month
Select a plan
Add to your order
- Coverage for accidental damage including drops, spills, and broken parts, as well as breakdowns (plans vary)
- 24/7 support when you need it.
- Quick, easy, and frustration-free claims.
Cover this product:
Select a plan
Enjoy fast, free delivery, exclusive deals, and award-winning movies & TV shows with Prime
Try Prime
and start saving today with fast, free delivery
Add a debit or credit card to save time when you check out
Convenient and secure with 2 clicks. Add your card
Frequently bought together
$49.98
Get it as soon as Saturday, May 11
In Stock
Total price:
To see our price, add these items to your cart.
Choose items to buy together.
Similar items that may deliver to you quickly
Page 1 of 1 Start overPage 1 of 1
From the manufacturer
Videos
Page 1 of 1Start OverPage 1 of 1
Videos for this product
3:26
Click to play video
La Crosse Technology Weather Station Review + Demo
DIY Life Tech
Videos for this product
1:40
Click to play video
Bright Display, Accurate Temps & a Forecast Feature.
Hooked And Rooted
Compare with similar items
This Item  La Crosse Technology Weather Station with Customizable Alerts, Weather Forecast, Temperature, Dew Point, Humidity, Time, Heat Index, Large Display, Adjustable Brightness, Wireless, Black, C85845-INT |  |  |  |  | |
| Price | -32% $49.98 List: $73.95 | $55.68 | -20% $39.99 List: $49.69 | -6% $46.75 Typical: $49.99 | -29% $23.37 List: $32.95 |
| Delivery | Get it as soon as Saturday, May 11 | Get it as soon as Saturday, May 11 | Get it as soon as Saturday, May 11 | Get it as soon as Saturday, May 11 | Get it as soon as Saturday, May 11 |
| Customer Ratings | |||||
| Easy to read | |||||
| Accuracy | |||||
| Tech Support | |||||
| Sold By | Amazon.com | Amazon.com | JLS LLC | Amazon.com | Amazon.com |
| power source | Corded Electric | Battery Powered | Ac/Dc | Battery Powered | Battery Powered |
| display type | LED | — | LCD | LCD | LCD |
| batteries included | ✗ | ✗ | ✗ | ✗ | ✗ |
Reviews with images
Hopefully a glitch in QC at factory - updated: replacement works great!
Seems like a good product, lots of information for the $$ spent.However, the QC at the factory missed - at least this one.10-digit of indoor humidity level has dead and weak segments. They are 8-segment numbers and several are either dead or weak on the 10-digit. Giving it 4-stars for now...Returning for a replacement.If the replacement works, then I will be happy. I will add information to how it works at that point...If the replacement shows the same or other defects, my review will be edited/appended and the stars "will plummet".NOTE: Amazon made the return process painless - they get 5 stars for that!=================Update, 02/16/2023 - now 5 stars!Have owned and used the replacement for ~6 days now.=> Display on replacement unit has ALL segments for all digits and information visible!What I like:-------------------*Easy to program. I set the clock deliberately "off" enough to check the WWV/NIST receiver. By next morning when it had found the transmitter, the clock was set!*Very bright display, even in a fully lit room. It can be read from across the kitchen. One small gripe, if they had auto-dimming feature, that would be fantastic. Like I said... VERY bright display...*Accurate as far as I can tell - indoor seems very accurate (see pics), the outdoor within +/- 2 degrees more or less (see pics). I have to say that outdoor, I am happy with that - I use it to get a general idea of if it is "sweater/fleece or T-shirt" weather anyway, not for precision measurements!-------------------I used a Fluke 179 multimeter with a "type K" thermocouple, Fluke 80BK-A to measure against the LaCrosse. The meter is "good for" 0.1 degree resolution with a 1% accuracy between -40F and +752F (!), however the thermocouple is listed as "Accuracy: +/- 2.2 °C or 2% whichever is greater ((0 to 260 °C)".All measurements were taken before sunrise, to avoid any solar "influence" on the outdoor readings.=> I will NOT say that my Fluke is more accurate than the LaCrosse station - I have no evidence to support that! And I will not go through the rigmarole of calibrating the thermocouple...*Outdoor sensor: placed it in the ribbed weather housing (LaCrosse 925-1418) they recommend and attached it to the north side of a 4"x4" post. One gripe there: the screwheads (Phillips) require a very "sharp" (read: new) screwdriver if you don't want to slip and round out the screw heads' "+" grooves. ...and predrill the holes for the screws!Not so fond of:-------------------*The "landscape" weather forecast. Yes, it has trend arrows, etc. But being "old school" I would like the barometer reading in numbers presented. The WX-station I replaced (Ac*rite) had a 12 hour barometer graph with numbers readings, that was nice!*Minor gripe: the buttons on top are labeled on the backside and since I have my station wall-mounted I need to take it down to read the button labels so I know which one to push (do YOU remember all buttons on all equipment you have?) Will print a label strip and attach on the front for my benefit...*Minor gripe 2: If they had made the major numbers a little smaller, they could have fit max/min reading numbers in w.o. you having to push the temp button to cycle through and view them...Summary:-------------------*Comes with AC adapter, and uses three AA-batteries for backup*Has all the information available that I want (except the barometer numbers...)*Shows trends (with arrows)*Shows min/max (requires button push)*Automatic time adjustment through the WWV/NIST receiver*Very bright and clear display. VERY bright...*Display is a bit "busy", and they seem to not knowing when to mix graphics, bars, and numbers.*I believe it to be a "good investment". Time will tell. I will recommend this, but do buy the outdoor housing for the sending unit!-------------------The Ac*rite it replaces has served us well, but started to give trouble with the remote sending units, one dying all together and the replacement not staying connected. Whether the connection issue is with the sending or receiving unit I have not figured out. Also, the Ac*rite display was getting very dim (yes, all new batteries and AC adapter connected) and the brightness is set to 100%... Perfect for a completely dark room, however, my kitchen is not. Can't complain - had it for MANY years...
Top reviews from the United States
There was a problem filtering reviews right now. Please try again later.
Reviewed in the United States on February 9, 2023
However, the QC at the factory missed - at least this one.
10-digit of indoor humidity level has dead and weak segments. They are 8-segment numbers and several are either dead or weak on the 10-digit. Giving it 4-stars for now...
Returning for a replacement.
If the replacement works, then I will be happy. I will add information to how it works at that point...
If the replacement shows the same or other defects, my review will be edited/appended and the stars "will plummet".
NOTE: Amazon made the return process painless - they get 5 stars for that!
=================
Update, 02/16/2023 - now 5 stars!
Have owned and used the replacement for ~6 days now.
=> Display on replacement unit has ALL segments for all digits and information visible!
What I like:
-------------------
*Easy to program. I set the clock deliberately "off" enough to check the WWV/NIST receiver. By next morning when it had found the transmitter, the clock was set!
*Very bright display, even in a fully lit room. It can be read from across the kitchen. One small gripe, if they had auto-dimming feature, that would be fantastic. Like I said... VERY bright display...
*Accurate as far as I can tell - indoor seems very accurate (see pics), the outdoor within +/- 2 degrees more or less (see pics). I have to say that outdoor, I am happy with that - I use it to get a general idea of if it is "sweater/fleece or T-shirt" weather anyway, not for precision measurements!
-------------------
I used a Fluke 179 multimeter with a "type K" thermocouple, Fluke 80BK-A to measure against the LaCrosse. The meter is "good for" 0.1 degree resolution with a 1% accuracy between -40F and +752F (!), however the thermocouple is listed as "Accuracy: +/- 2.2 °C or 2% whichever is greater ((0 to 260 °C)".
All measurements were taken before sunrise, to avoid any solar "influence" on the outdoor readings.
=> I will NOT say that my Fluke is more accurate than the LaCrosse station - I have no evidence to support that! And I will not go through the rigmarole of calibrating the thermocouple...
*Outdoor sensor: placed it in the ribbed weather housing (LaCrosse 925-1418) they recommend and attached it to the north side of a 4"x4" post. One gripe there: the screwheads (Phillips) require a very "sharp" (read: new) screwdriver if you don't want to slip and round out the screw heads' "+" grooves. ...and predrill the holes for the screws!
Not so fond of:
-------------------
*The "landscape" weather forecast. Yes, it has trend arrows, etc. But being "old school" I would like the barometer reading in numbers presented. The WX-station I replaced (Ac*rite) had a 12 hour barometer graph with numbers readings, that was nice!
*Minor gripe: the buttons on top are labeled on the backside and since I have my station wall-mounted I need to take it down to read the button labels so I know which one to push (do YOU remember all buttons on all equipment you have?) Will print a label strip and attach on the front for my benefit...
*Minor gripe 2: If they had made the major numbers a little smaller, they could have fit max/min reading numbers in w.o. you having to push the temp button to cycle through and view them...
Summary:
-------------------
*Comes with AC adapter, and uses three AA-batteries for backup
*Has all the information available that I want (except the barometer numbers...)
*Shows trends (with arrows)
*Shows min/max (requires button push)
*Automatic time adjustment through the WWV/NIST receiver
*Very bright and clear display. VERY bright...
*Display is a bit "busy", and they seem to not knowing when to mix graphics, bars, and numbers.
*I believe it to be a "good investment". Time will tell. I will recommend this, but do buy the outdoor housing for the sending unit!
-------------------
The Ac*rite it replaces has served us well, but started to give trouble with the remote sending units, one dying all together and the replacement not staying connected. Whether the connection issue is with the sending or receiving unit I have not figured out. Also, the Ac*rite display was getting very dim (yes, all new batteries and AC adapter connected) and the brightness is set to 100%... Perfect for a completely dark room, however, my kitchen is not. Can't complain - had it for MANY years...
Hopefully a glitch in QC at factory - updated: replacement works great!
Reviewed in the United States on February 9, 2023
Seems like a good product, lots of information for the $$ spent.Reviewed in the United States on February 9, 2023
However, the QC at the factory missed - at least this one.
10-digit of indoor humidity level has dead and weak segments. They are 8-segment numbers and several are either dead or weak on the 10-digit. Giving it 4-stars for now...
Returning for a replacement.
If the replacement works, then I will be happy. I will add information to how it works at that point...
If the replacement shows the same or other defects, my review will be edited/appended and the stars "will plummet".
NOTE: Amazon made the return process painless - they get 5 stars for that!
=================
Update, 02/16/2023 - now 5 stars!
Have owned and used the replacement for ~6 days now.
=> Display on replacement unit has ALL segments for all digits and information visible!
What I like:
-------------------
*Easy to program. I set the clock deliberately "off" enough to check the WWV/NIST receiver. By next morning when it had found the transmitter, the clock was set!
*Very bright display, even in a fully lit room. It can be read from across the kitchen. One small gripe, if they had auto-dimming feature, that would be fantastic. Like I said... VERY bright display...
*Accurate as far as I can tell - indoor seems very accurate (see pics), the outdoor within +/- 2 degrees more or less (see pics). I have to say that outdoor, I am happy with that - I use it to get a general idea of if it is "sweater/fleece or T-shirt" weather anyway, not for precision measurements!
-------------------
I used a Fluke 179 multimeter with a "type K" thermocouple, Fluke 80BK-A to measure against the LaCrosse. The meter is "good for" 0.1 degree resolution with a 1% accuracy between -40F and +752F (!), however the thermocouple is listed as "Accuracy: +/- 2.2 °C or 2% whichever is greater ((0 to 260 °C)".
All measurements were taken before sunrise, to avoid any solar "influence" on the outdoor readings.
=> I will NOT say that my Fluke is more accurate than the LaCrosse station - I have no evidence to support that! And I will not go through the rigmarole of calibrating the thermocouple...
*Outdoor sensor: placed it in the ribbed weather housing (LaCrosse 925-1418) they recommend and attached it to the north side of a 4"x4" post. One gripe there: the screwheads (Phillips) require a very "sharp" (read: new) screwdriver if you don't want to slip and round out the screw heads' "+" grooves. ...and predrill the holes for the screws!
Not so fond of:
-------------------
*The "landscape" weather forecast. Yes, it has trend arrows, etc. But being "old school" I would like the barometer reading in numbers presented. The WX-station I replaced (Ac*rite) had a 12 hour barometer graph with numbers readings, that was nice!
*Minor gripe: the buttons on top are labeled on the backside and since I have my station wall-mounted I need to take it down to read the button labels so I know which one to push (do YOU remember all buttons on all equipment you have?) Will print a label strip and attach on the front for my benefit...
*Minor gripe 2: If they had made the major numbers a little smaller, they could have fit max/min reading numbers in w.o. you having to push the temp button to cycle through and view them...
Summary:
-------------------
*Comes with AC adapter, and uses three AA-batteries for backup
*Has all the information available that I want (except the barometer numbers...)
*Shows trends (with arrows)
*Shows min/max (requires button push)
*Automatic time adjustment through the WWV/NIST receiver
*Very bright and clear display. VERY bright...
*Display is a bit "busy", and they seem to not knowing when to mix graphics, bars, and numbers.
*I believe it to be a "good investment". Time will tell. I will recommend this, but do buy the outdoor housing for the sending unit!
-------------------
The Ac*rite it replaces has served us well, but started to give trouble with the remote sending units, one dying all together and the replacement not staying connected. Whether the connection issue is with the sending or receiving unit I have not figured out. Also, the Ac*rite display was getting very dim (yes, all new batteries and AC adapter connected) and the brightness is set to 100%... Perfect for a completely dark room, however, my kitchen is not. Can't complain - had it for MANY years...
Images in this review
Reviewed in the United States on October 13, 2021
Very accurate and I really like the display. A few days after I bought this WeatherStation (C85845-1), they discontinued it and came out with a newer model (308-1414B-INT) I decided to see how well it worked and how much I liked they display.
In my opinion, the display on this older version is less cluttered and easier to read than the newer version, but that is personal preference. I think it also looks cleaner with the buttons hidden. It was a few dollars less than the newer version. It does everything I need which is inside and outside temperature and humidity. Interestingly, it has a bunch of alarms you can set for high temp, low temp, high humidity, low humidity etc.
I compared the lacrosse weather station with temperature and humidity I had on other devices. They were all within a degree of each other and a few percent humidity. I even used a Digital temperature gun to double check all the thermometers. I've checked it over a few days and it continues to be quite consistent. I have a north facing metal overhang that I can attach sensor unit to, with some padding to avoid transmitting any heat or cool from the overhang to the sensor. The sensors stay out of the sun and the rain, which is important.
I had a previous lacrosse model that was also a rain station. It was more basic and it chewed through batteries like crazy. This lacrosse model is powered by an AC adapter with battery back up. When you unplug the AC adapter, the display will stay lit for a few seconds and then it will dim. But you can still read it if you need to.
Like my other lacrosse unit, I found this one intuitive to use and it provides the useful information I need. I only had it turned on for about three days and I saw the forecast display change from "sunny" to "cloudy." Sure enough, it was cloudy all day.
I appreciate they put a dimmer on it as well as I have this in my den and I can dim the display when I watch TV. I don't get rain amounts anymore but I can get that from a slew of Wunder-stations in my neighborhood. I do like that I can get the precise temperature and humidity outside. We live in a hilly area so there are microclimates everywhere.
If you're looking for a relatively inexpensive, yet fairly full featured Basic WeatherStation, I don't think you'll go wrong with either finding this model on sale or the new model (308-1414B-INT). I have attached a picture to show well the looks like when I look at it from my chair
In my opinion, the display on this older version is less cluttered and easier to read than the newer version, but that is personal preference. I think it also looks cleaner with the buttons hidden. It was a few dollars less than the newer version. It does everything I need which is inside and outside temperature and humidity. Interestingly, it has a bunch of alarms you can set for high temp, low temp, high humidity, low humidity etc.
I compared the lacrosse weather station with temperature and humidity I had on other devices. They were all within a degree of each other and a few percent humidity. I even used a Digital temperature gun to double check all the thermometers. I've checked it over a few days and it continues to be quite consistent. I have a north facing metal overhang that I can attach sensor unit to, with some padding to avoid transmitting any heat or cool from the overhang to the sensor. The sensors stay out of the sun and the rain, which is important.
I had a previous lacrosse model that was also a rain station. It was more basic and it chewed through batteries like crazy. This lacrosse model is powered by an AC adapter with battery back up. When you unplug the AC adapter, the display will stay lit for a few seconds and then it will dim. But you can still read it if you need to.
Like my other lacrosse unit, I found this one intuitive to use and it provides the useful information I need. I only had it turned on for about three days and I saw the forecast display change from "sunny" to "cloudy." Sure enough, it was cloudy all day.
I appreciate they put a dimmer on it as well as I have this in my den and I can dim the display when I watch TV. I don't get rain amounts anymore but I can get that from a slew of Wunder-stations in my neighborhood. I do like that I can get the precise temperature and humidity outside. We live in a hilly area so there are microclimates everywhere.
If you're looking for a relatively inexpensive, yet fairly full featured Basic WeatherStation, I don't think you'll go wrong with either finding this model on sale or the new model (308-1414B-INT). I have attached a picture to show well the looks like when I look at it from my chair
Images in this review
Top reviews from other countries
Steve
Works well in Australia, but...
Reviewed in Australia on March 25, 2022
Steve
Reviewed in Australia on March 25, 2022
Unfortunately these devices only come supplied with a 110V mini Plug Pack, they are not designed to run from 240V even with a basic travel adaptor. Fortunately however they only need 5V which is the same voltage a USB port can produce so as per my pics all you need is to purchase an inexpensive USB to 3.5x1.35mm DC cable, connect it to an old USB Charger/Plugpack (or any USB port) and you're done! As seen in the photo, I'm using a USB Powerbank purely to demonstrate how easy this is to achieve but of course I'm using a small USB plugpack in its permanent location.
Note: the right-angle plug on the cable I bought off eBay (item: 154527783652) is a bit larger than the original so although it fits and works perfectly it isn't as neat & tidy as it could be.
Images in this review
